DIVAR IP 6000 2UDIP-6080-00N, DIP-6082-8HD, DIP-6083-8HD en Installation Manual
ChassisThe chassis includes 8 hard drive bays. The chassis accepts a 2U backplane, 3 fans and2 power supplies.BackplaneEach chassis comes with a 2U ba
Front view:1 Power Failure 5 Power2 Overheat/Fan Fail 6 Reset3 NIC1/NIC2 7 Power on/off4 HDD Rear view:26153412x mains connection 100 – 240 VAC,50
Control panel LEDsThe control panel located on the front of the chassis has LEDs to provide you with criticalinformation related to different parts of
Chassis setup and maintenanceThis chapter covers the steps required to install components and perform maintenance on thechassis.!Caution!Review the wa
Installing hard drivesThis chapter describes the removing and installing of hard drives.Removing hard drive traysThe drives are mounted in drive carri
Installing a hard driveThe drives are mounted in drive carriers.To install a hard drive to the hard drive carrier:1. Remove the screws securing the du
Notice!We recommend using the respective Bosch hard disk drives. The hard disk drives as one ofthe critical component are carefully selected by Bosch
Installing or replacing a DVD-ROM driveThe chassis models are not shipped with a DVD-ROM from factory as the OS is pre-installed onthe disk on module
1 DVD-ROM 2 Front port panelTo replace or install the front port panel:1. Turn off and unplug the unit.2. Remove the chassis cover.3. Disconnect the p
To install the air shroud:4 Place air shroud in the chassis. The air shroud fits behind the two fans closest to thepower supply. Note: If a 16 DIMM (1
!Warning!The fans might still be turning when you remove the fan assembly from the chassis. Keepfingers, screwdrivers, and other objects away from the
!Warning!Redundant power suppliesThis unit might have more than one power supply connection. To de-energize the unit, removeall connections.Replacing
Replacing the power distributorRedundant server chassis that are 2U or greater require a power distributor. The powerdistributor provides failover and
Rack installationThis chapter provides a quick setup checklist to get your chassis up and running. Followingthese steps in the order given should enab
– If the rack is provided with stabilizing devices, install the stabilizers before mounting orservicing the unit in the rack.– This unit should be mou
Notice!This rail will fit a rack between 26" and 33.5" deep.Separating the sections of the rack railsThe chassis package includes two rail a
Installing the inner railsThe chassis includes a set of inner rails in two sections: inner rails and inner rail extensions.The inner rails are pre-att
Locking TabsBoth chassis rails have a locking tab, which serves two functions. The first is to lock thesystem into place when installed and pushed ful
the chassis, then the two rear brackets positioned with just enough space to accommodatethe width of the Telco rack. Finish by sliding the chassis int
AppendixThis chapter gives information for supporting and troubleshooting.MotherboardAll graphics shown in this chapter were based upon the latest PCB
Table of contents1Safety precautions 51.1 General safety precautions 51.2 Electrical safety precautions 61.3 ESD precautions 71.4 Operating precaution
Motherboard component overviewFigure 5.2: Motherboard – component overviewX8SIL/X8SIL-F/X8SIL-V jumpersNumberJumper Description Default38 JPUSB1 BP US
X8SIL/X8SIL-F/X8SIL-V headers/connectorsNumber Connector Description4,16 COM1/COM2 COM1/2 Serial connection headers33,32,27,23,7 Fans 1~5 System/CPU f
Motherboard featuresCPU Single Intel Xeon 3400 series processor in an LGA1156 socket.Memory Four (4) 240-pin, DDR3 SDRAM DIMM sockets with support for
Two (2) USB ports on the rear IO panelFour (4) USB header connectors for front accessOne (1) Type A internal connectorKeyboard/MousePS/2 Keyboard/Mous
Drivers and software for Intel 3400/3420 chipset utilitiesOther ROHS 6/6 (Full Compliance, Lead Free)Dimensions Micro ATX form factor, 9.6" x 9.6
better performance than comparable systems. The X8SIL/X8SIL-F/X8SIL-V also features a TCOtimer (to enable the system to recover from a software/hardwa
the system to keep the required circuitry "alive". In case the system malfunctions and youwant to turn off the power, just press and hold th
For the X8SIL/X8SIL-F/X8SIL-V motherboard, iSCSI is supported on LAN 1. This can beenabled through the BIOS: Advanced => PCI/PnP Configuration =>
Basically, the RAID controller writes the raidconfiguration - information (COD = configuration-on-disk) in an only field on each disk managed by the c
- 2 disks missing- 2 disks "foreign configuration" or "unconfigured good"The rebuild only could start, when the other three disks
4.3.5 Installing the chassis into a Telco rack 274.4 Turning on the system 285Appendix 295.1 Motherboard 295.1.1 Motherboard layout 295.1.2 Motherboar
In this example, we choose a start sequence 5800 (from 6412) and all 612 events left. We finda timestamp, that PD (Physical Drive) 6 was removed. PD 4
How to use the MegaCLI Command-Line UtilityUse a bootable DOS USB stick with XMS manager "himem.sys" and start the MegaCLI.exe.Please see th
seqNum: 0x00001893Time: Mon Jul 19 13:52:41 2010 Code: 0x00000065Class: 2Locale: 0x02Event Description: Rebuild failed on PD 04(e0xfc/s4) due to sourc
Adapter: 0 - Number of Events : 288seqNum: 0x0000188fTime: Mon Jul 19 13:52:41 2010Code: 0x000000fcClass: 3Locale: 0x01Event Description: VD 00/0 is n
All disks are seen, but configuration is marked as not importable; click Cancel and viewConfiguration 2. It is the same; this means, a complex situati
Use the event viewer or MegaCLI to identify the "first failed" disk.In this example, disk in Slot 4 was first fail, Slot 7 second fail. Clic
Now in logical view we see disk online and a degraded RAID. Click on disk 4 to get in the PDmenu. Click on correct row, on "Global" or "
An unconfigured good drive is displayed. Right-click this drive and choose a hotspare type.You see the rebuild is starting at once.MegaCLI Commandline
MegaCli -vMegaCli -help|-h|?MegaCli -adpCountMegaCli -AdpSetProp {CacheFlushInterval -val} | { RebuildRate -val}| {PatrolReadRate -val} | {BgiRate -va
| BootWithPinnedCache | AutoEnhancedImportDsply | AutoDetectBackPlaneDsbl| CopyBackDsbl | LoadBalanceMode | UseFDEOnlyEncrypt | WBSupport | EnableJBOD
Safety precautionsObserve the safety precautions in this chapter.General safety precautionsFollow these rules to ensure general safety:– Keep the area
-Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALLMegaCli -LDGetProp -Cache | -Access | -Name | -DskCache -Lx|-L0,1,2|-LALL-aN|-a0,1,2|-aALLMegaCli -getLdExpansionIn
MegaCli -AdpEventLog -GetSinceReboot {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALLMegaCli -AdpEventLog -IncludeDeleted {-i
MegaCli -AdpInfoCompare {-checkFw <string> | -checkID -hex | -checkBatt -val | -checkDimm -val} -aN|-a0,1,2|-aALLMegaCli -adpFwDumpMegaCli -AdpN
Bosch Sicherheitssysteme GmbHRobert-Bosch-Ring 585630 GrasbrunnGermanywww.boschsecurity.com© Bosch Sicherheitssysteme GmbH, 2014
!Warning!Lithium battery:Batteries that have been inserted wrongly can cause an explosion. Always replace emptybatteries with batteries of the same ty
– Use only one hand when working with powered-on electrical equipment. This is to avoidmaking a complete circuit, which will cause electrical shock. U
Note:Please handle used batteries carefully. Do not damage the battery in any way. A damagedbattery may release hazardous materials into the environme
System overviewDIVAR IP 6000 is an affordable, simple and reliable all-in-one recording management solutionfor network surveillance systems of up to 6
Komentarze do niniejszej Instrukcji