Bosch D720 Przewodnik Instalacji Pobierz pdf (Strona 54)

D9412GV3/D7412GV3 | Operation and Installation Guide | 10.0 Off-Board Relays

54 Bosch Security Systems, Inc. | 2/10 | F01U143070-01

To install OctoRelays in the enclosure with the control

panel:

1. Align the module with one of the mounting

locations in the enclosure (refer to Figure 2 on

page 10).

2. Using the screws provided with the module,

secure the module in the enclosure.

Use the D137 Mounting Bracket or D9002

Mounting Skirt to install OctoRelays in enclosures

with no available module mounting locations.

10.1.4 Wiring Connections

Power down the control panel to connect OctoRelays.

Refer to Figure 23 on page 52 and Figure 24 on page

53.

OctoRelays for Relays 1 to 64 connect to

Zonex 1, Terminal 28.

OctoRelays for Relays 65 to 128 connect

to Zonex 2, Terminal 26 on the

D9412GV3 only.

Only one OctoRelay is shown wired to each Zonex

bus in Figure 23 on page 52and Figure 24 on page

53. Wire additional OctoRelays in parallel. Review

Section 6.0 Power Outputs on page 27 for information

about providing enough power for the relays.

The number of D8129 OctoRelays that can be

connected to each Zonex terminal on the D9412GV3

control panels is limited by the number of D8128D

OctoPOPITs connected.

Using D8129 OctoRelays and D8128D

OctoPOPITs together on the same Zonex

terminals is limited and depends on the

number of D8128 OctoPOPITs and

D8129 OctoRelays connected to a single

Zonex Bus.

Refer to Table 19 for information about

the maximum number of D8128Ds and

D8129s you can connect to a single

Zonex bus.

Table 19: Number of D8128Ds Used with

D8129s

If the number of

D8128Ds connected to a

single Zonex bus is:

Do not connect more

than this number of

D8129s:

9 6

10 5

11 4

12 3

13 1

14 1

10.2 D811 Arm Status Relay Module

The D811 Arm Status Relay Module allows the

addition of a single off-board relay output to the

system. Alarm output, auxiliary relay, sensor reset,

arming status, point status, alarm memory, or remote

functions can be assigned to the D811 relay output. It

is not restricted to the Arming Status Mode only.

Relay Numbers for D811 Not Programmable: If the

D811 is connected to Zonex 1, Terminal 28, use relay

number 53 for the relay output. If the D811 is

connected to Zonex 2, Terminal 26 on the

D9412GV3, use relay number 117 for the relay

output.

D811 Modules connect as shown in Figure 25 on

page 55and Figure 26 on page 56. Review Section

6.0 Power Outputs on page 27 to ensure that enough

power is provided for the powered devices that

connect to the system. Refer to Relay Parameters in

the D9412GV3/D7412GV3 Program Entry Guide

(P/N: F01U143071) for programming details.

D811 Restricted for Fire Systems: The D811 relay

output is not supervised and cannot be used in fire or

combined fire and burglary installations for primary

indication devices.

10.2.1 Relay Output

Relay outputs can activate when you are

programming the control panel.

Disconnect equipment connected to relay

outputs when you perform this function.

Each D811 relay output provides a Form C dry

contact rated for 1.0 A at 12.0 VDC. Normally-open,

common, and normally-closed terminals are available.

When an individual output is activated, continuity

exists between the normally-open and common

terminals. When the output is not activated, continuity

exists between the normally-closed and common

terminals.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 75 76

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch D720 Przewodnik Instalacji Strona 54

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Klawiatury numeryczne Bosch D720