Bosch GTK 40 Dokumentacja Strona 17
- Strona / 157
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
English | 17
Bosch Power Tools 1 609 929 U13 | (17.8.12)
Correction of Malfunctions
Accessories
For more information on the complete quality accessories
program, please refer to the Internet under
www.bosch-pt.com or contact your specialist shop.
Problem Cause Corrective Measure
The pneumatic tool is ready for operation, but no staples
(GTK 40) or brads (GSK 50) are discharged.
A staple (GTK 40) or a brad (GSK 50) has become jammed in
the shot duct.
–Clear the jam.
(See “Clearing Jams”, page 16)
The magazine slider is 11 defective. – Clean and lubricate the magazine slider 11 as required
and make sure that the magazine 8 is not dirty/soiled.
The spring of the magazine slider is too week or defective. – Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The fasteners being used are not permitted. – Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble “Technical Data” may be used.
The magazine 8 is empty. – Refill the magazine.
(See “Loading the Magazine”, page 15)
The staples (GTK 40) or brads (GSK 50) are discharged very
slowly and with too little pressure.
The rated pressure of the compressed-air supply is too low. – Increase the compressed-air supply. 8 bar may not be
exceeded.
The driver blade is damaged. – Use only the lubricants recommended by Bosch.
(See “Lubricating the Pneumatic Tool”, page 16)
The sealing ring of the piston is worn or damaged. – Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The buffer is worn. – Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The length and diameter of supply-air hose 17 do not corre-
spond with the data of this pneumatic tool.
– Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 14)
The supply-air hose 17 is bent/creased. – Correct the bend/crease in the supply-air hose.
The staples (GTK 40) or brads (GSK 50) are driven in too
deep.
The rated pressure of the compressed-air supply is too high. – Reduce the compressed-air supply. 5 bar may not be
fallen below.
The depth stop is set too deep. – Adjust the depth stop to the desired depth.
(See “Adjusting the Depth Stop”, page 16)
The buffer is worn. – Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The staples (GTK 40) or brads (GSK 50) are not driven in
deep enough.
The rated pressure of the compressed-air supply is too low. – Increase the compressed-air supply. 8 bar may not be
exceeded.
The depth stop is set too high. – Adjust the depth stop to the desired depth.
(See “Adjusting the Depth Stop”, page 16)
The length and diameter of supply-air hose 17 do not corre-
spond with the data of this pneumatic tool.
– Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 14)
The supply-air hose 17 is bent/creased. – Correct the bend/crease in the supply-air hose.
The pneumatic tool skips staples (GTK 40) or brads (GSK 50)
or has a too large cycle feed.
The fasteners being used are not permitted. – Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble “Technical Data” may be used.
The magazine 8 is not operating correctly. – Clean and lubricate the magazine slider 11 as required
and make sure that the magazine 8 is not dirty/soiled.
The spring of the magazine slider is too week or defective. – Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The sealing ring of the piston is worn or damaged. – Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The staples (GTK 40) or brads (GSK 50) frequently jam in the
shot duct.
The fasteners being used are not permitted. – Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble “Technical Data” may be used.
– Contact an authorised service agent for Bosch power
tools.
The driven staples (GTK 40) or brads (GSK 50) are bent.
The driver blade is damaged. – Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
Contrary to working with normal operating speed, the staples
(GTK 40) or brads (GSK 50) are not driven in deep enough
enough at higher operating speeds.
The interior diameter of the supply-air hose is too low. – Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 14)
The compressor is not suitable for fast operating speeds. – Use a compressor that is sufficiently dimensioned for
the number of connected pneumatic tools and the op-
erating speed.
OBJ_BUCH-1038-003.book Page 17 Friday, August 17, 2012 10:59 AM
- ΕΎϤϴϠόΗϞϴϐθΘϟΔϴϠλϷ 1
- GSK 50 GSK 50 4
- GTK 40 GTK 40 4
- GTK 40 GSK 50 5
- Sicherheitshinweise 8
- Produkt- und Leistungs 9
- 10 10
- Magazin bestücken 10
- Auslösesysteme 10
- Inbetriebnahme 10
- Arbeitshinweise 10
- Wartung und Service 11
- 12 12
- Behebung von Störungen 12
- Änderungen vorbehalten 13
- Assembly 15
- Operation 15
- Maintenance and Service 16
- English 17
- Correction of Malfunctions 17
- Accessories 17
- Français 18
- Fonctionnement 20
- Français 21
- Instructions d’utilisation 21
- Nettoyage et entretien 21
- 22 22
- Plan de maintenance 22
- Guide de dépannage 22
- Instrucciones de seguridad 23
- 24 24
- Utilización reglamentaria 24
- Componentes principales 24
- Operación 25
- 26 26
- Puesta en marcha 26
- Mantenimiento y servicio 27
- Português 28
- Português 29
- Componentes ilustrados 29
- Montagem 30
- Português 31
- Sistemas de disparo 31
- Colocação em serviço 31
- Indicações de trabalho 31
- Manutenção e serviço 32
- Português 33
- Eliminação de avarias 33
- Sob reserva de alterações 34
- Montaggio 36
- Manutenzione ed assistenza 37
- 38 38
- Programma di manutenzione 38
- Eliminazione di guasti 38
- Nederlands 39
- 40 40
- Gebruik volgens bestemming 40
- Afgebeelde componenten 40
- 42 42
- Ingebruikneming 42
- Tips voor de werkzaamheden 42
- Onderhoud en service 43
- Wijzigingen voorbehouden 44
- Montering 46
- Vedligeholdelse og service 47
- 48 48
- Serviceplan 48
- Afhjælpning af fejl 48
- Säkerhetsanvisningar 49
- Svenska 51
- Påfyllning av magasin 51
- Utlösningssystem 51
- Driftstart 51
- Arbetsanvisningar 51
- Underhåll och service 52
- Ändringar förbehålles 53
- 54 54
- Formålsmessig bruk 54
- Illustrerte komponenter 54
- Service og vedlikehold 56
- Norsk 57
- Vedlikeholdsplan 57
- Utbedring av feil 57
- Turvallisuusohjeita 58
- Tuotekuvaus 59
- Käyttöohjeet 60
- Hoito ja huolto 61
- ÅëëçíéêÜ 62
- ÅëëçíéêÜ 63
- Óõíáñìïëüãçóç 64
- Ëåéôïõñãßá 65
- ÓõíôÞñçóç êáé Service 66
- ÅëëçíéêÜ 67
- ÅîïõäåôÝñùóç âëáâþí 67
- Ôçñïýìå ôï äéêáßùìá áëëáãþí 68
- Ürün ve işlev tanm 69
- Bakm ve servis 71
- 72 72
- Aksesuar 72
- Wskazówki bezpieczeństwa 73
- 74 74
- Dane techniczne 74
- Konserwacja i serwis 76
- Polski 77
- Usuwanie usterek 77
- Bezpečnostní upozornění 78
- Popis výrobku a specifikací 79
- Údržba a servis 81
- 82 82
- Plán údržby 82
- Odstranění poruch 82
- Změny vyhrazeny 83
- Popis produktu a výkonu 84
- Používanie 85
- Slovensky 87
- Odstraňovanie porúch 87
- Zmeny vyhradené 88
- Magyar 89
- Rendeltetésszerű használat 89
- Összeszerelés 90
- Üzemeltetés 91
- Karbantartás és szerviz 92
- Magyar 93
- Tartozékok 93
- Vevőszolgálat és tanácsadás 93
- Eltávolítás 93
- Óêàçàíèÿ ïî áåçîïàñíîñòè 94
- Îïèñàíèå ïðîäóêòà è óñëóã 95
- Ðàáîòà ñ èíñòðóìåíòîì 96
- Òåõîáñëóæèâàíèå è ñåðâèñ 97
- 98 98
- Óñòðàíåíèå íåèñïðàâíîñòåé 98
- Âîçìîæíû èçìåíåíèÿ 99
- Îïèñ ïðîäóêòó ³ ïîñëóã 100
- Leinfelden, 16.08.2012 101
- Åêñïëóàòàö³ÿ 102
- Óêðà¿íñüêà 103
- Óñóíåííÿ íåñïðàâíîñòåé 103
- 104 104
- Ïðèëàääÿ 104
- Ìîæëèâ³ çì³íè 105
- Descrierea produsului şi a 106
- Funcţionare 107
- Întreţinere şi service 108
- Română 109
- Remedierea deranjamentelor 109
- Sub rezerva modificărilor 110
- Îïèñàíèå íà ïðîäóêòà è 111
- Ìîíòèðàíå 112
- Ïîääúðæàíå è ñåðâèç 113
- 114 114
- Ïëàí çà òåõíè÷åñêî îáñëóæâàíå 114
- Îòñòðàíÿâàíå íà ïîâðåäè 114
- Uputstva o sigurnosti 115
- Opis proizvoda i rada 116
- 118 118
- Puštanje u rad 118
- Uputstva za rad 118
- Održavanje i servis 119
- Zadržavamo pravo na promene 120
- Opis in zmogljivost izdelka 121
- Obratovanje 122
- Vzdrževanje in servisiranje 123
- 124 124
- Načrt vzdrževanja 124
- Odprava motenj 124
- Hrvatski 125
- Opis proizvoda i radova 126
- Održavanje i servisiranje 128
- Hrvatski 129
- Otklanjanje smetnji u radu 129
- Zadržavamo pravo na promjene 130
- Kasutamine 132
- Hooldus ja teenindus 133
- Latviešu 134
- Izstrādājuma un tā darbības 135
- Lietošana 137
- Apkalpošana un apkope 138
- Latviešu 139
- Piederumi 139
- Lietuviškai 140
- Gaminio ir techninių duomenų 141
- Montavimas 141
- 142 142
- Paleidimo sistema 142
- Paruošimas darbui 142
- Darbo patarimai 142
- Priežiūra ir servisas 143
- Galimi pakeitimai 144
- ﻦﺋﺎﺑﺰﻟﺍ ﺓﺭﻮﺸﻣﻭ ﺔﻣﺪﺧ 145
- ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺓﺪﻌﻟﺍ ﻦﻣ ﺺﻠﺨﺘﻟﺍ 145
- ﻞﻠﳋﺍ ﺔﻟﺍﺯﺇ 146
- ﺔﻣﺪﳋﺍﻭ ﺔﻧﺎﻴﺼﻟﺍ 147
- ﻥﺰﺨﳌﺍ ﺊﻠﻣ 148
- (B2–B1 ﺭﻮﺼﻟﺍ ﻊﺟﺍﺭ) GTK 40 148
- ﻕﻼﻃﻻﺍ ﺔﻤﻈﻧﺃ 148
- ﻞﻴﻐﺸﺘﻟﺍ ﺉﺪﺑ 148
- ﻞﻐﺷ ﺕﺎﻈﺣﻼﻣ 148
- ﻥﺎﻣﻷﺍ ﺕﲈﻴﻠﻌﺗ 150
- ﺀﺍﺩﻷﺍﻭ ﺞ 150
- ﺘﻨﳌﺍ ﻒﺻﻭ 150
- ﻩﺎﮕﺘﺳﺩ ﻥﺩﺮﮐ ﺝﺭﺎﺧ ﻩﺩﺭ ﺯﺍ 151
- ﺲﯾﻭﺮﺳ ﻭ ﺖﺒﻗﺍﺮﻣ 153
- ﯽﻠﻤﻋ یﺎﻫ ﯽﺋﺎﻤﻨﻫﺍﺭ 154
- ﻥﺁ ﺩﺮﮑﻠﻤﻋ ﻭ ﻩﺎﮕﺘﺳﺩ ﺢﯾﺮﺸﺗ 156
- ﯽﻨﻓ ﺕﺎﺼﺨﺸﻣ 156
- ﯽﻨﻤﯾﺍ یﺎﻫ ﯽﺋﺎﻤﻨﻫﺍﺭ 157
Powiązane produkty i podręczniki dla Gwoździarki pneumatyczne Bosch GTK 40
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 1.911 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji