Bosch D9412GV4 Przewodnik Instalacji Pobierz pdf (Strona 117)

D9412GV4/D7412GV4/D7212GV4 Panel and Area Wide Parameters | en 117

Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03

M## CC Address 1 [through #]

Programming this prompt determines at which CC address setting this menu item appears.

3.14 Relay Parameters

Relays provide dry contact (normally open or normally closed) outputs for LED annunciation

and other applications as well as wet voltage outputs (12 VDC on or off) for basic alarm

system functions (such as Bell Output or Reset Sensors). The applications are endless, but

mainly, relays enhance a system’s capacity to perform output functions.

– Panel-Wide Relays: These relays provide an output related to a panel-wide indication.

For annunciation, these relays can indicate system-wide troubles for power and phone.

They also provide an overall control panel summary of alarms, troubles, and supervisory

conditions.

– Area Relays: These relays provide an output by the area to which the relay is assigned.

An area can have its own bell and sensor reset indications. Relays can also indicate the

area armed state and whether any off-normal conditions, such as a Force Arm, occurred.

– On Board Relays: Three on-board 12 VDC voltage outputs provide power when activated

on the control panel. These outputs are programmed at the factory as Relays A, B, and C.

Typically, Relay A (Terminal 6) is used for the bell, Relay B (Terminal 7) is used for an

alternate alarm output (such as another bell), and Relay C (Terminal 8) is used for Sensor

Reset (Relays B and C require the optional D136 Relays).

– Off-Board Relays: The D9412GV4 can also control 128 (64 for the D7412GV4) dry-

contact form C relays when up to sixteen optional D8129 OctoRelay Modules are

installed. These relays are used for Area Relay, Panel-Wide Relay, and Individual Point

Fault Relays.

– Relay Follows Point: Relays can also be used to activate when a point programmed for

P## Relay Response Type (refer to Section P## Relay Response Type, page 138) is off-

normal or in an alarm condition.

– Relay Reports: When relay activity is reported to the receiver (refer to

Section 3.3 Routing, page 23), on-board relays are reported as follows:

A = 253

B = 254

C = 255

The others report as 001 to 128. The Relay Report is RELAY SET RELAY # rrr when the

relay is turned on and RELAY RESET RELAY # rrr when the relay is turned off. Relay

Reports are also printed on the local printer and stored in the control panel memory log.

– Controlling Relays: Relays can activate depending upon conditions that exist with the

control panel. In addition, the user can control relays by using the Change Relay?

function, Relay On/Relay Off skeds, and the Remote Account Manager.

Before programming your relays:

NOTICE!

There is no restriction on how many times you can assign a specific function to the menu. By

assigning a specific function more than once, you can assign the same function at different

keypads so that their order is different in different areas.

Default: M1, M2, M13, M15 are Yes for CC1 through CC16M3 .. M12, M14, M16

.. M32 are No for CC1 through CC16

Selection: Yes or No

Yes This menu item appears at this keypad address.

No This menu item does not appear at this keypad address.

1 2 ... 112 113 114 115 116 117 118 119 120 121 122 ... 209 210

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch D9412GV4 Przewodnik Instalacji Strona 117

Komentarze do niniejszej Instrukcji