Bosch D9412GV4 Przewodnik Instalacji Strona 52
- Strona / 210
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
52 en | Panel and Area Wide Parameters D9412GV4/D7412GV4/D7212GV4
F.01U.218.312 | 04 | 2012.03 Program Entry Guide Bosch Security Systems, Inc.
This prompt enables a report to be sent when the control panel or an SDI2 bus power supply
module detects a low or missing battery.
3.7 Printer Parameters
Up to three D9131A Parallel Printer Interface Modules can be connected to a D9412GV4 (one
printer for a D7412GV4 and a D7212GV4) SDI bus. Each printer is identified by an address of
17, 18, or 19. Options are available for Routing Reports and area assignments.
P## Area Assign
Assign an area to the printer programmed in Printer Address.
P## Supervised
Supervise this SDI address. Generate Trouble SDI ## Reports and local trouble annunciation if
a problem occurs with this printer or the SDI bus.
Yes Battery Failure and Restoral Reports are sent to the central station.
Modem Reports: Missing or shorted: BATTERY MISSING
Discharge below 12.1 VDC: BATTERY LOW
No Battery Failure and Restoral Reports are not sent to the central station.
NOTICE!
To comply with NFPA standards and UL 864 requirements for Commercial Fire systems
(D9412GV4 and D7412GV4), program this item as Yes.
Default: 1
Selection: 1 to 32 for D9412GV4
1 to 8 for D7412GV4
1 to 4 for D7212GV4
Default: No
Selection: Yes or No
Yes Only one printer can be installed for this printers SDI address.
No More than one unsupervised printer can be installed using this printers
SDI address and the same address DIP switch setting.
NOTICE!
Unsupervised printers sharing the same address setting print the same text.
NOTICE!
Trouble SDI ## Reports are always reported as Area 1, Account 1 Events regardless of where
the SDI device is assigned.
NOTICE!
When P## Supervised is set to Yes and all Printer Event Groups (such as P## Fire Events, P##
Burglar Event, or P## Usr Chng Evt) are set to No, the control panel does not generate
Trouble SDI ## Reports for the printer if the D9131A becomes disconnected.
NOTICE!
The printer cannot show area numbers greater than Area 8. When printed, Areas 9 and higher
print as 00.
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 2.271 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji