Bosch D9412GV4 Dokumentacja Pobierz pdf (Strona 13)

Notice!

For UL Certified accounts, additional power can be obtained using only a UL Listed auxiliary

12.0 VDC regulated, power-limited power supply.

Notice!

All terminals accept for Outputs A, B, and C (Terminals 6, 7 and 8) are supervised.

Wiring D125B to G-series control panels

CCD 0x - 0xxxx - 000 © RADIONICS INC.

D125B

1992

SWITCH

POWER

EARTH

GND

ZONE

4 5

PANEL

COMMON

ZONE

B-

LOOP

A-

LOOP

B+

LOOP

A+

LOOP

R21

R10

R14

R11

R12

R22

RV2

RV3

RV4

RV1

TB1/J1

R13

PTC2

PTC1

D125B

4, 5

7, 9

6, 8

ZONEX COMMON

EARTH

COMMON

BATTERY NEGATIVE ONLY

BATTERY POSITIVE ONLY.

RELAY A

RELAY B

RELAY C

+ AUX POWER

CLASS 2 TRANSFORMER

16.5 VAC 40 VA 60 Hz

Model D1640

Internally Fused - Do not short

Requires Unswitched Outlet

Do not share with other equipment

S4 GROUND FAULT DETECT

Enabled

Disabled

RED

ON when communicating

OFF when idle

Commercial Protected-Premises Control Panel

System is intended to be checked by a Qualified Technician at least every 3 years.

The types of initiating circuits the control panel has been approved for are A, M, W, SS.

The types of signaling the control panel has been approved for are DAC, OT, NC, RevPol.

VOLTAGE RANGES

Open 3.7 - 5.0 VDC Short 0.0 - 1.3 VDC

Normal 2.0 - 3.0 VDC

SDI

RED

POWER +

YELLOW

DATA BUS A

GREEN

DATA BUS B

BLACK

COMMON

ZONEX OUT 1

ZONEX IN 1

NFPA

Style 4.0

Signaling

Line

Circuits

F01U201283-03

LEDs Off when Normal

YELLOW - Charging Status

RED - Low Battery - 12.1 VDC

10.2 VDC - Battery Load Shed

This equipment should be installed in accordance with the NFPA 70 (National Electrical Code) and

NFPA 72 (National Fire Alarm Code).

D9412GV4

ZONEX POWER +

PHONE LINE SEIZED LED

TIP

RING

TELCO CORD MODEL D161

POWER SUPPLY REQUIREMENTS

The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all

Accessory Devices. For System Loading, refer to the GV4 Series Control Panel

Operation and Installation Guide (P/N: F01U201527).

Guide (P/N: F01U201527) for Power Requirements relating to Terminals 6 and 7 .

CAUTION:

Refer to the GV4 Series Control Panel Operation and Installation

All external connections except Terminal 5 (battery positive) are inherently power

limited. Requirements for battery standby time might reduce allowable output.

WARNING!

Multi-Battery installation requires

Model D122 or D122L Dual Battery

Harness. Improper installation can

be a fire hazard.

Battery: Replace every 3 to

5 years with one or two Model

D126 or D1218 12 V Lead Acid

Batteries.

PROGRAMMABLE

ALARM OUTPUTS

Terminals

SWITCHED AUX

and

Terminal

Operation

Monitor

LED

Pulses when

Normal

Flickers when

Ringing

GREEN

Point 3

Point 4

1614 15

Point 1

Point 2

1211 13

Point 5

Point 6

Point 7

Point 8

Incorrect wiring will

damage this equipment.

Suitable for dry indoor

use only.

Devices powered by any

power output must

be supervised.

Minimum system requirements for Classification in accordance with ANSI/SIA CP-01-2010

UL Listed and Classified control unit Model D9412GV4, D7412GV4, or D7212GV4;

UL Listed and Classified keypad Model D1256, D1257, D1260, D1255, D1255R, or D1255RB;

UL Listed Local Bell

WARNING!

To prevent risk of

electric shock,

disconnect AC

power and

telephone lines

before servicing.

CAUTION:

Avoid damage to Panel.

Do not connect 24 V to terminals.

Maximum charging current 1.4 A

ZONEX OUT 2

ZONEX IN 2

Not suitable for remote station protected premises services where separate transmission circuits

are required for fire, supervisory (when applicable) and trouble signals when using D185.

The D9412GV4 Control Panel is UL Listed For Central Station, Remote Station, Local, Auxiliary,

Proprietary, and Household Fire Alarm, and Central Station, Local, Proprietary,

Police Station Connect, Household Burglar Alarm

and Encrypted Line Security when

communicating via a network.

SDI2

RED

POWER +

YELLOW

DATA BUS A

GREEN

DATA BUS B

BLACK

COMMON

Refer to the GV4 Series Control Panels Approved Applications Compliance

Guide (P/N: F01U201525) for System Wiring Diagram, Issue A and for

compatible smoke detectors. 2-wire Compatible Identifier “A”.

SDI Connector

SDI2 Connector

Figure 3.3: Wiring two-wire loops using a D125B (D9412GV4 shown)

Callout ￚ Description Callout ￚ Description

1 ￚ Switched auxiliary power from the

control panel’s relay C

7 ￚ Power-limited, supervised negative to A

LOOP detectors

2 ￚ Supervised connection to Zone B power

from an on‑board point of the panel

8 ￚ Power-limited, supervised positive to B

LOOP detectors

3 ￚ Supervised connection to Zone A power

from an on‑board point of the panel

9 ￚ Power-limited, supervised positive to A

LOOP detectors

4/5 ￚ Connection from control panel

COMMON (one connection only)

10 ￚ Earth ground

6 ￚ Power-limited, supervised negative to B

LOOP detectors

3.2.2

Control Panel Diagrams | en 13

Bosch Security Systems, Inc. UL Installation Instructions 2014.04 | 03 | F.01U.291.483

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 39 40

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch D9412GV4 Dokumentacja Strona 13

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ochrona przeciwpożarowa Bosch D9412GV4