Bosch GV2 Series Przewodnik Instalacji Pobierz pdf (Strona 7)

D9412GV2/D7412GV2

D9412GV2/D7412GV2 Release Notes for Version 7.05

Remote Arm/ Disarm Output

Prompt:

Remote Warning

When enabled, this feature uses the Alarm Bell output

to annunciate the arming and disarming of an area by

remote means, such as by keyswitch, key fob, or

remote software (RPS, BIS Security Engine). When

arming occurs, the output pulses for two seconds.

When disarming occurs, the output pulses ON, OFF,

ON, OFF for two seconds each.

Abort Window

Prompts:

CC# Abort

Display, P

# Alarm Abort

Abort Window

This feature is always enabled, but it only applies to

intrusion alarm events generated by points that have

P# Alarm Abort

set to Yes and

P## Invisible Pt

set

to No. When an intrusion alarm event is annunciated,

the user has the duration of time programmed in the

Abort Window

prompt to enter a valid passcode to

prevent the alarm event from being transmitted to the

central station. When transmission is aborted

successfully, any keypad with

CC# Abort Display

set

to Yes shows ALARM NOT SENT.

Cancel Window

Prompt:

CC# Cancel Display

The burglary alarm cancel window is enhanced by an

optional keypad display. When

CC# Cancel Display

is set to Yes and

Cancel Report

is set to Yes, an

alarm silence operation after event transmission

displays CANCEL RPT SENT on the keypad. The

burglary alarm cancel window duration is the time

programmed in the

A# Alarm Bell

prompt.

Duress Passcode

Prompts:

Duress Type

A# Duress Enable

L## Send Duress

A new duress option is available that allows any

passcode with the

L# Send Duress

permission set to

Yes to always send a Duress Alarm event upon entry.

This feature allows the control panel to have uniquely

dedicated passcodes for all users. Additionally, when

this feature is enabled, the Passcode +1 and +2

features are disabled for compliance with SIA CP-01-

2000 regulations.

Swinger Shunt Enhancement

Prompt:

Swinger Count

The Swinger Bypass feature is enhanced to allow a

variable number of faults before automatically

bypassing a point. When a point with

P# Swinger

Bypass

set to Yes is faulted the number of times

programmed in

Swinger Bypass Count

, it is

automatically bypassed.

Power-Up Standby

When the control panel is powered up, or the system

is rebooted, all points are now temporarily bypassed

for 60 seconds. This feature is always enabled and has

no configuration parameters.

Walk Test Enhancements

The Walk Test procedure is enhanced to provide

more user feedback. The Walk Test now indicates that

the menu is ready to time out, and clearly notifies the

user at all keypads in the area of operation when a test

is in progress. Additionally, the Walk Test procedure

issues point trouble conditions for any 24-hour points

that remain off-normal when the Walk Test menu idle

time expires. These enhancements are always enabled

and have no configuration parameters.

3.2 Version 7.01

3.2.1 D1260 Keypad Enhancements

The D1260 Keypad must have firmware version 1.03

or above to operate with the GV2 Series Control

Panels. An update kit (P/N: R19-D1260-0103) is available

from Customer Service: (800) 289-0096.

Custom Function Enhancements: The custom

functions now support the soft keys (the eight

unmarked keys around the display) on the D1260

Keypad. This change makes the operation of custom

functions on D1260 Keypad easier to program.

D1260 Keypads with firmware version 1.03 or above

do not need to check the control panel firmware

revision when communicating with GV2 Series

Control Panels; therefore, the Display Revision

(COMMAND 59) keypad (command center) function

can be password protected.

The D1260 and D1260B Keypads can be used with

CC# Supervision

set to No to allow multiple

Enhanced Keypads at the same address.

1 2 3 4 5 6 7 8 9 10 11 12

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch GV2 Series Przewodnik Instalacji Strona 7

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch GV2 Series