Bosch GV2 Series Przewodnik Instalacji Pobierz pdf (Strona 8)

D9412GV2/D7412GV2

D9412GV2/D7412GV2 Release Notes for Version 7.05

3.2.2 New Firmware Features:

Two Man Rule: Two Man Rule requires two unique

passcodes to be entered at the same keypad to disarm

an area. Without the second passcode, the system

denies entry. Two Man Rule requires the presence of

two people at opening, providing added security.

Early Ambush: Early Ambush requires two passcode

entries on the same keypad or on two separate

keypads located in the same area. Enter the same

passcode twice or enter two unique passcodes,

depending upon the configuration. The first entry

disarms the area and the second entry stops a timer

programmed to send a duress event. If the second

entry does not occur within the preset time, the system

generates a duress event. Early Ambush allows users

to inspect the premises and use the system to confirm

that the area is safe to enter, providing added security.

Easy Exit Control:

The GV2 Series Control Panels change from one

armed state to another armed state without disarming.

For example, if you change the state from Master Arm

to Perimeter Arm, the control panel complies and

reports the change. Easy Exit Control reduces the

number of keystrokes and simplifies system operation.

Passcode-controlled Menus: The system prompts a

user to enter a passcode before viewing the keypad

function list menu. The system shows the user the

menu options allowed according to the user’s authority

level. Passcode-controlled menus simplify system

operation by providing a user with unique and

pertinent options and information. This feature is not

intended for use on D1256 Fire Keypads.

Passcode Follows Scope: Use Passcode Follows

Scope to restrict passcode arming and disarming only

to the keypad’s immediate local area. Passcode

Follows Scope simplifies the arming and disarming

procedure without limiting any other keypad

command capabilities.

Invisible Walk Test: A function list menu item allows

the user to test invisible interior- or perimeter-

controlled and non-controlled (24-hr) points within the

scope of the keypad without sending a report to the

central station.

Door Activated Custom Function: A custom

function activates when user credentials are presented

to the reader of a D9210B Access Control Interface

Module. A custom function behaves as though the

user performed a function at the keypad associated

with the door controller. This feature is available only

on the D9412GV2 and D7412GV2.

Latest Close Time: The Extend Close

(COMMAND 51) function is enhanced with a

programmable latest closing time.

4.0 Upgrading to a GV2 Series

Control Panel

Remote Programming Software (RPS) version 3.7.160

or above is required to upgrade an existing G Series

Control Panel installation to a GV2 Series Control

Panel. Because the GV2MAIN and GV2AUX

handlers cannot read the configuration data from a G

Series Control Panel, using RPS is the only method

available to convert an account’s existing panel type to

a D9412GV2 or D7412GV2.

Refer to the RPS help files for the specific control

panel for additional information on control panel

conversion. In the RPS help file, select:

Panel Specific Information9000 Series

Control/CommunicatorsCommunicating with

9000 Series PanelsUpgrading a Panel Type

Hardware Enhancements

• The control panel has an SDI bus quick-connect

terminal (Molex

connector) next to the S1 reset

switch. This connector provides an easy way to

connect an SDI device to the SDI bus without

disconnecting the wires on SDI Terminals 29

through 32. To order SDI wiring harnesses, use

the following part numbers: Molex to Molex

(P/N: C321) and Molex to terminal

(P/N: PKWH).

This SDI terminal is not compatible with

the D5200 Programmer.

• Two new posts next to the on-board telephone

jack allow easy connection of a butt set or

telephone for troubleshooting purposes. The posts

are labeled TIP and RING.

The telephone line supervision time might

be affected when a butt set or telephone is

connected to the telephone terminal posts.

• On-board Relays B (Terminal 7, labeled Alt

Alarm) and C (Terminal 8, labeled SW Aux) are

now installed in the factory. No supplemental

installation or purchase is necessary to prepare

these terminals for use.

1 2 3 4 5 6 7 8 9 10 11 12

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch GV2 Series Przewodnik Instalacji Strona 8

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch GV2 Series