Bosch D7212GV2 Przewodnik Instalacji Pobierz pdf (Strona 40)

D7212GV2 | Operation and Installation Guide | 9.0 Off-Board Points

40 Bosch Security Systems, Inc. | 2/07 | F01U003805-02

Table 15: Switch 5 Settings for Line Termination

Is a D8125 POPEX Module

connected?

Switch 5 Setting(s) on

D8128D OctoPOPIT(s)

Set Switch 5 of only one

D8128D to ON

Yes

Set Switch 5 of all

D8128Ds to OFF

Point DIP Switches

Each point connected to the D8128D is enabled by

closing the respective DIP switch, or disabled by

opening the DIP switch. For example, to disable a

device connected to the P3 Terminal (Point 3), move

DIP switch number 3 to the OPEN position.

Use the point DIP switches to disable conflicting

points, such as when a D9210B Access Control Module

must be assigned to a point that falls within the range

of the D8128D OctoPOPIT. In this example, a

D9210B is assigned to Point 20. On the same system, a

D8128D OctoPOPIT is assigned to Points 17 through

24. Moving the DIP switch for Point 4 to the OFF

position would effectively disable Point 20, allowing

normal operation of the D9210B and the OctoPOPIT.

Terminate each OctoPOPIT sensor loop with a 1 kΩ

EOL resistor. Attach a resistor even if you do not

enable the loop.

9.4.5 Mounting OctoPOPITs

The D8128D OctoPOPIT Module can be installed in

the enclosure with the control panel using standard

four-conductor 0.8 mm (22 AWG) wire, or in a

separate enclosure (Model D8103, D8103A, or D8109)

up to 61 m (200 ft.) from the control panel using

shielded (recommended) standard four-conductor

0.8 mm (22 AWG) wire. If using the D125B or D129,

refer to the Specifications section of the D8128D

Installation Guide (P/N: 41323) for cabling

requirements.

For UL Listed systems, mount the D8128D in a

tamper-proof enclosure. To install OctoPOPITs in the

control panel’s enclosure, complete the following

procedure. Use the D137 Mounting Bracket to install

OctoPOPITs in enclosures with no module-mounting

locations available.

1. Align the OctoPOPIT module using any of the

four mounting locations in the enclosure. Refer to

Figure 2 on page 14.

2. Use the screws provided with the module to secure

it in the enclosure.

9.4.6 Wiring OctoPOPITs

Warning: Disconnect all power to the

control panel before beginning any work

with the internal components. Serious injury

could result from electrical shock.

1. Power down the control panel:

Disconnect the positive (red) battery lead at the

battery.

Unplug the transformer.

A D8128D OctoPOPIT can be installed up

to 61 m (200 ft.) from the control panel.

2. Connect the D8128D to the control panel, using

either of the following methods:

•

Wire the D8128D to the terminal strip on the

side of the POPEX Module (refer to Using the

Terminal Strip on page 40), or

•

Connect the D8128D using the Molex

connectors (P1 and P2). Refer to Using Molex®

Connectors on page 42.

Caution - AC induction: Avoid installing

Zonex data wires and Zonex input (sensor

loop) wires around any AC conduit, wiring,

or electrical devices that emit fields of

electromagnetic interference (EMI).

Using the Terminal Strip

Refer to Table 16 and to Figure 18 on page 41 when

using the terminal strip to connect the D8128D

OctoPOPIT to the control panel.

Table 16: Terminal Strip Connections

D8128D D7212GV2

Common Terminal 23

Out Terminal 27

In Terminal 28

+12 V Terminal 24

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 59 60

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch D7212GV2 Przewodnik Instalacji Strona 40

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch D7212GV2