Bosch D7212GV2 Przewodnik Instalacji Pobierz pdf (Strona 52)

D7212GV2 | Operation and Installation Guide | 14.0 D7212GV2 Faceplate

52 Bosch Security Systems, Inc. | 2/07 | F01U003805-02

14.0 D7212GV2 Faceplate

Figure 28: D7212GV2 Faceplate

TELCO

RING

TIP

PHONE LINE

SEIZED

EARTH GROUND

COMMON

RELAY A

RELAY B

RELAY C

+ AUX POWER

CLASS 2 TRANSFORMER

16.5 VAC 40 VA 60 Hz

Model D1640

Internally Fused - Do not short

Requires Unswitched Outlet

Do not share with other equipment

GROUND FAULT DETECT

Enabled

Disabled

Digital Alarm Communicator Transmitter

D7212GV2 Control Panel is UL Listed for Household Fire Alarm, and Central Station, Local,

Police Station Connect, Household Burglar Alarm

and Encrypted Line Security when

communicating via a network.

System is Intended To Be Checked By A Qualified Technician At Least Every 3 Years.

The types of initiating circuits for which the control panel has been approved are A, M, W, SS.

VOLTAGE RANGES

Open 3.7 - 5.0 VDC

Normal 2.0 - 3.0 VDC

Short 0.0 - 1.3 VDC

Reset Pin

Disable All Except Battery

Charging And Programming

PERIPHERAL DEVICE CONNECTIONS

RED POWER +

YELLOW DATA BUS A

GREEN DATA BUS B

BLACK COMMON

ZONEX OUT 1

ZONEX IN 1

N.F.P.A.

Style 4.0

Signaling

Line

Circuits

F01U003800-01

1211 13

Point 1 Point 2

1514 16

Point 3 Point 4

1817 19

Point 5 Point 6

2120 22

Point 7 Point 8

LEDs Off When Normal

Charging Status

Low Battery - 12.1 VDC

YEL

RED

10.2 VDC - Battery Load Shed

This equipment should be installed in accordance with the NFPA 70 (National Electrical Code)

and NFPA 72 (National Fire Alarm Code) for Local, Central Station, Remote Station, Proprietary and

Household Fire Warning Systems and under the limits of the Local Authority Having Jurisdiction

(National Fire Protection Association, Battermarch Park, Quincy, MA 02269). Printed information

describing proper installation, operation, testing, maintenance, evacuation planning and repair

service is to be provided with this equipment.

D7212GV2

NOT USED

ZONEX POWER +

ZONEX COMMON

SDI Connector

Refer to

D7212GV2 Approved Applications Compliance Guide

(P/N: F01U003806)

For System Wiring Diagram, Issue A and for Compatible Smoke Detectors

BATTERY NEGATIVE ONLY

BATTERY POSITIVE ONLY

CAUTION:

Avoid damage to Panel.

Do not connect 24 V to terminals.

Maximum charging current 1.4 A

PHONE

LED

RED

ON when

communicating

OFF when idle

PHONE LINE SEIZED

TIP

RING

TELCO CORD

MODEL D161

CAUTION:

Refer to

D7212GV2 Operation and Installation Guide

POWER SUPPLY REQUIREMENTS

The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all

Accessory Devices. For System Loading, refer to

D7212GV2 Operation and

Installation Guide

(P/N: F01U003805).

All external connections except Terminal 5 (battery positive) are inherently power

limited. Requirements for battery standby time might reduce allowable output.

(P/N: F01U003805) for Power Requirements relating to Terminals 6 and 7 .

WARNING!

Multi-Battery installation requires

Model D122/D122L Dual Battery

Harness. Improper installation can

be a fire hazard.

Battery: Replace every 3 to

5 years with one or two Model

D126 or D1218 12V Lead Acid

Batteries.

GRN

Point 8

S3 Option

Closed = 1K EOL

Normal Operation

Open =AB-12 UL

Bell Box 220 K

D5200/D5360

PROG CONN

Incorrect wiring will

damage this equipment.

Suitable for dry indoor

use only.

Devices powered by the

AUX power output must

be supervised.

Minimum system requirements for Classification in accordance with ANSI/SIA CP-01-2000:

UL Listed and Classified control unit Model D9412GV2, D7412GV2, or D7212GV2;

UL Listed and Classified keypad Model D1256, D1257, D1260, D1255, D1255R, or D1255RW;

UL Listed Local Bell

PROGRAMMABLE

ALARM OUTPUTS

Terminals

SWITCHED AUX

and

Terminal

1 - Charging status LED (yellow)

2 - Low battery LED (red)

3 - Color-coded battery leads

4 - Ground fault detect enable

5- Phone LED (red)

6 - Tip

7- Telephone cord connector

8- Ring

9- S3, Point 8 EOL selection

10- Operation monitor LED (green)

11- Accessory connector

12- Programming connector

13- Reset pin

14- SDI quick connector

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch D7212GV2 Przewodnik Instalacji Strona 52

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch D7212GV2