Bosch DS7445i Podręcznik Użytkownika Strona 41
- Strona / 54
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
DS7240/DS7220 User's Guide Copyright 2002 Detection Systems, Inc. P/N: 49211C Page 41
PART II: KEYPAD USER’S GUIDE: DS7445i LED KEYPAD
Zone LED # LED Function Description
On Telephone Line Fail
Flashing Slow Comm Fail, Destination 1
1
Flashing Fast Comm Fail, Destination 2
2 On Alternate Comm Trouble
On Installer Switch Closed3
Flashing Fast Installer Switch is open &
either User 1 PIN or Installer
PIN (or both) are at default
settings
On Backup Battery Low4
Flashing Slow Backup Battery Missing
5 On Bell Supervision Fail
On RF Receiver Jammed6
Flashing Slow RF Receiver Trouble
On Data Bus Device Missing
Flashing Slow Data Bus Tamper
7
Flashing Fast Data Bus Device
Trouble/Reset
On System Fault
Flashing Slow System Interval
8
Flashing Fast Ground Fault Condition
Table 12: Viewing System Troubles
4. Press the [#] key twice to exit the View System
Trouble function.
5.22 View Zone Trouble
I can perform this function.
I cannot perform this function.
Key Sequence: [#] + [4] + [8]
Description
Use this function to view which zones (if any) are in
trouble.
Procedure
1. Make sure that the system is turned off (Armed
LED is off).
2. Enter a valid user PIN.
3. Enter [#] + [4] + [8].
The keypad then displays all zones that are in
trouble (if any) by turning on their respective
LEDs.
The DS7445i LED Keypad can only show Zones
1-16.
See Table 13 for LED Zone Trouble displays.
Zone Trouble Condition
Off No Zone Trouble
On Wiring Fault
Flashing Slow RF Sensor Low Battery
Flashing Fast RF Sensor Missing
Table 13: Viewing Zone Troubles
4. Press the [#] key twice to exit this function.
5.23 System Test
I can perform this function.
I cannot perform this function.
Key Sequence: [#] + [4] + [1]
Description
The System Test function allows you to make sure
that your system is operating correctly by testing the
system’s bell, strobe, battery and phone line. Your
Security Company programs which system
components are tested (for example, your system
may only be programmed to test the battery and the
bell).
I
c
a
n
t
e
s
t
:
System Bell
System Strobe
Battery
Phone Line
If any of these components fails to test, contact your
Security Company for assistance. Be sure to contact
your Security Company before you begin the system
test.
Procedure
1. Make sure the system is off (Armed LED is off).
2. Enter a valid user PIN.
3. Enter [#] +[4] + [1].
The system starts the test. As each test is
underway, the corresponding zone LED turns on.
Zone LED # System Test Component
1 Bell
2 Strobe (may take up to 20 minutes)*
3 Backup Battery (may take up to 4 minutes)*
4 Phone Line (may take up to 10 minutes)*
Table 14: System Test LED Indications
* To skip to the next test, press the [*] key.
When testing the bell and strobe, check for
bell/strobe activation. The LED testing status
does not indicate bell/strobe test failure (LED
does not flash fast upon test failure).
As the system tests each component, the
corresponding LED displays the stage of each
test.
Zone LED Testing Status
Flash Slow Testing Segment Underway
Flash Fast Testing Segment Failed
On Testing Segment Complete
Table 15: System Test Status
4. When the system test is complete, the keypad
automatically exits this function.
To stop the test currently in progress and skip to
the next test, press the [*] key. To abort all tests,
press the [#] key.
- User’s Guide for the 1
- MY ALARM COMPANY IS: 2
- Contents 3
- Part I: Introduction 4
- 3.0 Keypad Overview 5
- 3.2 Keypad Tones 6
- 3.3 Keypad LED Functions 6
- 3.4 Function Key Sequences 7
- 3.5 System Events 7
- 3.8 Logging Out of the System 7
- Part II: Keypad User’s Guide 8
- 4.7 Set Partial On Zones 10
- 4.10 Force Arming the System 12
- 4.11 View Faulted Zones 13
- 4.12 Bypass Zones 13
- 4.13 Date and Time 14
- 4.14 Change PIN 14
- 4.15 Change Others’ PINs 15
- 4.17 Add a PIN 16
- 4.18 Delete a PIN 17
- 4.19 Renew One-Time PINs 17
- 4.20 Check System Troubles 18
- 4.21 View Alarm Memory 18
- 4.22 View System Trouble 19
- 4.23 View Zone Trouble 19
- 4.24 System Test 19
- 4.25 Walk Test 20
- 4.26 Reset the System 21
- 4.27 Turn Chime On/Off 21
- 4.28 Select Chime Tone 21
- 4.29 Select Chime Zones 22
- 4.30 Extend Auto-On Time 22
- 4.31 Change Skeds 22
- 4.32 Change Outputs 25
- 4.33 Remote Program 26
- 4.34 All Areas Off 26
- 4.35 All Areas On 26
- 4.36 Move to Area 27
- 4.37 Auto-Forward On Setup 27
- 4.38 Auto-Forward Off Setup 28
- 4.39 Auto-Forward On/Off 28
- 4.41 View Log 29
- 5.1 Silence Alarms 30
- 5.2 Keypad Adjust 30
- 5.3 Turn the System Off 30
- 5.4 Turn the System All On 31
- 5.7 Set Partial On Zones 32
- Flashing Armed LED 33
- 5.10 Force Arming the System 34
- 5.11 Bypass Zones 35
- 5.12 Date and Time 35
- I can perform this function 36
- 5.17 Delete a PIN 39
- 5.18 Renew One-Time PINs 39
- 5.19 Check System Troubles 40
- 5.20 View Alarm Memory 40
- 5.21 View System Trouble 40
- 5.22 View Zone Trouble 41
- 5.23 System Test 41
- 5.24 Walk Test 42
- 5.25 Reset the System 42
- 5.26 Turn Chime On/Off 42
- 5.29 Extend Auto On Time 44
- 5.30 All Areas On 44
- 5.31 All Areas Off 44
- 5.32 Auto Forward On/Off 44
- 5.34 Remote Program 45
- Part III: Reference Materials 46
- 7.0 Panel Event Descriptions 47
- 10.0 Maintenance and Service 52
- 11.0 Power Failure 52
- 12.0 How to Clean the Keypad 52
- 13.0 Glossary 53
- Detection Systems, Inc. 6/02 54
- P/N: 49211C Page 54 of 54 54
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch DS7445i
(175 strony)
(44 strony)
(8 strony)
(64 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.141 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji