Bosch B450 Przewodnik Instalacji Strona 120
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Select this option to enable the Answering Machine Bypass feature when the system is armed.
When the system is disarmed, the control panel does not answer any incoming calls. This
option is beneficial in high telephone traffic installations where the control panel could
answer an incoming call.
8 – Use Bell 103 for FSK Format (Disabled=CCITT V21)
If this option is selected, the control panel uses the BELL 103 transmission frequency at 300
baud. If this option is not selected, the control panel uses the CCITT V21 transmission
frequency at 300 baud.
Item Location Default
Communicator Options 1 177 9
Value Description
1 Reporting functions allowed
2 Remote arming by telephone allowed
4 Answering machine bypass only when arrived
8 Use bell 103 for FSK format (Disabled=CCITT V21)
Communicator Options 2
1 – Arm/Disarm Reports Only if Previous Alarm
When selected, an Disarm Report is transmitted to the base station receiver when the system
is disarmed after an alarm occurred. When the system is armed, an Arming Report is
transmitted. An Arm or Disarm Report does not report again until the system registers another
alarm.
For a partitioned control panel, an Arm/Disarm Report is sent only for the area in which the
alarm occurred.
Notice!
If the system is disarmed when an alarm occurs, only an Arm Report is sent the next time the
system is armed.
A User Code with a priority set to Always Send Arm/Disarm Reports overrides this feature
(Arm/Disarm Reports are always sent for that User Code).
2 – Arm/Disarm Reports for STAY Mode 1 and STAY Mode 2
Select this option if Arm/Disarm Reports are required when the system is armed in STAY Mode
1 or STAY Mode 2.
If this option is selected, a Partial Arm Report is sent when the system is armed in STAY Mode
1 or STAY Mode 2.
4 – Delay Siren until Transmission Complete
If this option is selected, horn speaker, bell, and strobe outputs are not activated until after
the control panel sends the message and the base station receiver sends a kiss-off back to the
control panel. If multiple messages are transmitted, the sirens are activated after the last kiss-
off is sent.
If a Codepad Panic, Codepad Fire, or Codepad Medical Alarm is activated, horn speaker, bell,
and strobe outputs operate immediately.
8 – Extend Time to Wait for Handshake from 30 to 60 Sec
13.11
120 en | Communicator Information Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji