Bosch B450 Przewodnik Instalacji Strona 70
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Changing and Deleting User Codes
This function allows a Master Code holder to change or delete a User Code.
When using a partitioned Control Panel, the Master Code holder cannot add, change, or delete
User Codes unless the User Code is allocated to the same area as the Master Code. Refer to
User Code Priority, page 126 for more information.
1. Enter your Master Code and press [1][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the number of the code (1 to 32) you want to change and press [AWAY]. Two beeps
sound and the corresponding zone indicator lights.
3. Enter the new code and press [AWAY]. Two beeps sound and the STAY and AWAY indicators
are extinguished.
4. Repeat this procedure to change other User Codes.
Notice!
This function is automatically terminated if you do not press a button within 40 sec or if you
press [AWAY].
One long beep indicates that the code already exists or you entered an incorrect user
number.
Example
To program User Code number 2 as 4627, enter: [2 5 8 0 1][AWAY][2][AWAY][4 6 2 7][AWAY]
To delete a User Code:
1. Enter your Master Code and press [1][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the number of the code (1 to 32) you want to delete and press [AWAY]. Two beeps
sound and the corresponding zone indicator lights.
3. Press [STAY] to delete the User Code. Two beeps sound and the STAY and AWAY indicators
are extinguished.
4. Repeat this procedure to delete other User Codes.
Notice!
This function terminates automatically if you do not press a button within 40 sec or if you
press [AWAY]. One long beep indicates that the code already exists or that you entered an
incorrect user number.
Changing and Deleting Remote Radio User Codes
This function allows a Master Code holder to change or delete a remote radio User Code.
To Add a WE800EV2 Keyfob
Set RF receiver as WE800EV2 Receiver. Confirm that the keyfob has been added to the
WE800EV2 receiver. Refer to WE800EV2, page 29 – Add/delete keyfobs.
Enter your Master Code, followed by [1] and the [#] button (for example, [25801#]).
Enter the WE800EV2 keyfob number (301 to 332) you want to add, followed by the [#] button.
Up to 21 WE800EV2 keyfobs can be added, but only current keyfob number (1 to 16 ) displays
through zone indicators on the ICON codepad.
7.2.2
7.2.3
70 en | System Functions Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji