Bosch B450 Przewodnik Instalacji Strona 85
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Z1 COM Z2
Z1 COM Z2
Z1 COM Z2
1
2
3
4
NO
ZONE 1
NO
NC
NC
NC
NC
NC
Z1 COM Z2
NC ZONE 1
TAMPER
TAMPER
ZONE 1
ZONE 5 (ICP-SOL2-P)
ZONE 9 (ICP-SOL3-P)
(3K3 EOL) (6K8 EOL)
1K0
1K0
ZONE 5 (ICP-SOL2-P)
ZONE 9 (ICP-SOL3-P)
(6K8 EOL)
ZONE 1
(3K3 EOL)
Callout - Description
1 – Zone without resistor (Location 266 = 0 (No EOL)
2 – Single Zone input (Location 266 = 1k, 1k5, 2k2, 3k3, 3k9, 4k7, 5k6, 6k8, 10k, 12k, 22k)
3 –Double Zone with tamper (Location 266 = 14 [Split EOL3K3 / 6K8 with tamper
4 – Double Zone input (Location 266 = 15 (Split EOL 3k3 / 6k8))
Zone Programming
The programming information for each zone is stored in seven locations divided into three
groups. The first three locations determine how the zone operates, the next two locations set
up a number of zone options, and the last two locations store the communicator reporting
information for the zone.
Zone Operating Information
These locations store the Zone Type (for example, Delay-1, Instant, or 24-Hour), the Zone
Pulse Count, and the Zone Pulse Count Time. The Zone Pulse Count specifies the number of
times the zone must activate within the time specified in the Zone Pulse Count Time. Refer to
Zone Types, page 90, Zone Pulse Count, page 92, and Zone Pulse Count Time, page 92 for
more information.
Zone Options
These two locations allow you to select from a number of options. Refer to Zone Options 1,
page 93 and Zone Options 2, page 94 for more information.
Zone Reporting Information
This information includes the locations for the Zone Reserved and the Zone Report Options.
The Zone Reserved determines if the control panel sends Alarm Reports for the zone.
The Zone Report Options location enables you to specify how a zone reports to a base station
receiver. Refer to Zone Report Options, page 95 for more information.
9.3
Control Panel Zone Information | en 85
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji