Bosch B450 Przewodnik Instalacji Strona 144
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Codepad Panic Report
A Panic Alarm Report (Contact ID Event Code 120) is sent to the base station receiver when a
user presses either [1] and [3] or [STAY] and [AWAY] at the same time. A Panic Alarm is
audible, but you can program the alarm as silent by selecting Option 1 in Location 493.
Codepad Fire Report
A Fire Alarm Report (Contact ID Event Code 110) is sent to the base station receiver when a
user presses [4] and [6] at the same time. A Fire Alarm is audible, but you can program the
alarm as silent by selecting Option 2 in Location 493. A distinct fire sound is emitted through
the horn speaker to indicate this type of alarm. The fire sound is different than the burglary
sound.
Codepad Medical Report
A Medical Report (Contact ID Event Code 100) is sent to the base station receiver when a user
presses [7] and [9] at the same time. A Medical Alarm is audible, but you can program the
alarm as silent by selecting Option 4 in Location 493.
AUX Power Supply Fail Report
A System Trouble Report (Contact ID Event Code312) is sent when either the codepad AUX
power supply is blown or the AUX power supply malfunctions. The system reports the event
approximately 10 sec after the failure.
AUX Power Supply Fail Restore Report
A System Trouble Restore Report (Contact ID Event Code 312) is sent when the AUX power
supply is reset. The system reports the event approximately 10 sec after power supply is
reset.
AC Fail Report
An AC Fail Report (Contact ID Event Code 301) is sent to the base station receiver when the
AC MAINS supply is disconnected for 2 min. If you do not want an AC Fail Report to be sent
until the AC MAINS supply is disconnected for 1 hour, select Option 1 in Location 494. If you
want to ignore AC Fail, select Option 2 in Location 494.
AC Fail Restore Report
An AC Fail Restore Report is sent when the AC MAINS supply is connected continuously for
longer than 2 min.
Low Battery Report
A Battery Test Failure Report (Contact ID Event Code 302) is sent to the base station receiver
when the system’s battery voltage falls below 11 VDC or when a Dynamic Battery Test detects
a low capacity battery.
The control panel continually monitors the battery voltage. A Dynamic Battery Test is done
every time the system is armed and every 4 hours after the control panel is powered up.
17.12
17.13
17.14
17.15
17.16
17.17
17.18
17.19
144 en | Reports Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji