Bosch B450 Przewodnik Instalacji Strona 44
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
To copy the direct link adapter memory to the control panel:
1. Enter the Installer Code (the default is 1234) and press [#] to enter Installer’s
Programming Mode. Two beeps sound and the STAY and AWAY indicators flash on the
remote codepad to indicate you entered Installer’s Programming Mode. The remote
codepad displays the data stored in Location 0000.
2. Connect the direct link adapter to the Bosch SDI2 Bus pins at the bottom of the control
panel printed circuit board.
3. Enter [9 6 3 #]. Two beeps sound after the direct link adapter’s data is successfully
copied to the control panel. A long beep indicates that the direct link adapter is corrupt
and must be erased to clear the corrupt data.
4. Enter [9 6 0 #] to exit from Installer’s Programming Mode. The STAY and AWAY indicators
are extinguished on the remote codepad to indicate the system is disarmed.
5. Remove the direct link adapter from the control panel Failure to exit from Installer’s
Programming Mode before removing the direct link adapter can corrupt the direct link
adapter.
Command 965 - Set up Domestic Dialing Format
Command 965 simplifies the setup of the domestic dialing format to a one-step operation.
To set up domestic dialing format:
1. Enter the Installer Code (the default is 1234) and press [#] to enter Installer’s
Programming Mode. Two beeps sound and the STAY and AWAY indicators flash on the
remote codepad to indicate you entered Installer’s Programming Mode. If on a text
codepad, go to menu 81 Address Program. The remote codepad displays the data Mode.
The remote codepad displays the data stored in Location 0000.
2. Enter [9 6 5 #]. The command automatically sets Receiver 1 to domestic reporting and
sets other locations or Receiver 2 only (refer to the table Command 965 Defaults below).
No other locations are changed when you issue command 965.
3. If on a text codepad, enter the Installer Code (the default is (1234) and press [#] to enter
Installer’s Programming Mode. Go to menu 747 Set Up Domestic Dialing Format, then
save and exit.
The transmission format is automatically set for domestic dialing and the Subscriber ID
Number set for one identification beep. All reports, except Zone Status reporting and System
Status reporting, are allocated to Receiver 1 for domestic dialing.
Zone Status Reports including Zone Bypass, Zone Trouble, Sensor Watch, and Alarm Restore
codes, and System Status Reports including AUX Power Supply Fail, AC Fail, Low Battery, and
Access Denied Reports are allocated to Receiver 2 and do not report unless Receiver 2 is also
set up to report.
Location
Description Default Value Setting
033 Transmission Format 4 Domestic
034 and 039 Subscriber ID Number 0, 0, 0, 0, 0, 1 1 Beep
392 Zone Status Reporting Options 2 Receiver 2 only
403 Arm/Disarm Reporting Options 2 Receiver 2 only
424 System Status – Access Denied 6 Access Denied
427 System Status Reporting Options 2 Receiver 2 only
5.1.7
44 en | Configuration Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji