Bosch B450 Przewodnik Instalacji Pobierz pdf (Strona 131)

Item Option

Event Code 4 0 = Reserved

4 1 = Reserved

4 2 = Reserved

4 3 = Reserved

4 4 = Reserved

4 5 = Chime

4 6 = Zone not sealed

4 7 = Zone not sealed after Exit Time

4 8 = Reserved

4 9 = AC MAINS cycle (60 Hz or 50 Hz)

4 10 = Area 1 – zone unsealed

4 11 = Area 2 – zone unsealed

4 12 = Reserved

4 13 = Reserved

4 14 = Reserved

4 15 = Reserved

5 0 = Reserved

5 1 = Reserved

5 2 = Area 1 in alarm

5 3 = Area 2 in alarm

5 4 = Reserved

5 5 = Reserved

5 6 = Area 1 armed

5 7 = Area 2 armed

5 8 = Reserved

5 9 = Reserved

5 10 = Area 1 disarmed

5 11 = Area 2 disarmed

5 12 = Reserved

5 13 = Reserved

5 14 = Any areas armed

5 15 = Any areas disarmed

Event Code

6 0 = Reserved

6 1 = Reserved

6 2 = Remote control 4

6 3 = Remote control 5

6 4 = Remote control 6

6 5 = Remote control 7

6 6 = Remote control 8

6 7 = Remote control 9

6 8 = Remote control 10

6 9 = Remote control 11

6 10 = Remote control 12

Polarity (Modes) 0 = Output not used

1 = Normally open, going low

2 = Normally open, pulsing low

3 = Normally open, one shot low

4 = Normally open, one shot low (reactivate)

5 = Normally open, one shot low (can reset)

6 = Normally open, one shot low (alarm)

7 = Normally open, latching low

8 = Normally low, going open

9 = Normally low, pulsing open

10 = Normally low, one shot open

11 = Normally low, one shot open

(reactivate)

12 = Normally low, one shot open (can

reset)

13 = Normally low, one shot open (alarm)

14 = Normally low, latching open

Time Base 0 = Not Used

1 = 200 ms

2 = 1 sec.

3 = 1 min.

4 = 1 hr.

Time Base Multiplier Enter a value between 00 and 99.

Table 15.2: Output Item Options

* One Shot Mode

When you program the output polarity as one shot, the time base is multiplied by the time

base multiplier. (For example, if the time base = 2 and the multiplier = 05, the output operates

for 5 sec.)

*Pulsing Mode

When you program the output polarity as pulsing, the time base becomes the ON time and the

multiplier becomes the OFF time. The OFF time is the time base x the multiplier. (For

example, if you want the output to pulse 1 sec. ON and 5 sec. OFF, you would program time

base as one and the multiplier as five.)

Control Panel Programmable Outputs | en 131

Installation Guide 2014.07 | 00n | F01U298026

1 2 ... 126 127 128 129 130 131 132 133 134 135 136 ... 151 152

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch B450 Przewodnik Instalacji Strona 131

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450