Bosch B450 Przewodnik Instalacji Strona 55
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Notice!
Consequences
To arm the system in STAY Mode 2:
1. Press and hold [0].
2. When two beeps sound, release the button.
The STAY indicator is lit and the Exit Time starts.
The indicators for any zones that are programmed to be automatically isolated in STAY Mode 2
flash until the Exit Time expires. At the end of Exit Time, the zone indicators are extinguished
and the codepad sounds one short beep.
If a zone is not sealed at the end of Exit Time, the zone is automatically isolated and is lit
constantly on the remote codepad. The zone becomes an active part of the system again as
soon as it is resealed. For example, if a window is open when Exit Time expires, the window
does not become an active part of the system until it is closed. Opening the window after Exit
Time expires causes an alarm.
Forced Arming
Arming the system when a zone is not sealed is known as forced arming. Refer to
Section14.3.7Zone Options2on page 63 to enable forced arming for each zone.
If the STAY indicator does not light and a long beep sounds when attempting to arm the
system, forced arming is not permitted. If this is the case, you must seal all zones or manually
isolate them before you can arm the system.
Disarming the system from STAY Mode 2
There are two methods to disarm the system from STAY Mode 2. You can always use the first
method. You can use method two only if Option 4 is enabled in Location 497 (refer to
Section18.6Consumer
Options2on page 83).
To disarm the system from STAY Mode 2 (method one):
1. Enter your code and press [STAY].
2. Two beeps sound and the STAY indicator is extinguished. The system is now disarmed.
To disarm the system from STAY Mode 2 (method two):
A flashing zone indicator represents a previous alarm in that zone. If this is the case, a valid
User Code is required to disarm the system using method one. To enable method two, Option
4 in Location 497 must
be enabled (refer to Section18.6ConsumerOptions2on
page 83).
1. Press and hold [0].
2. When two beeps sound, release the button.
The STAY indicator is extinguished and the system is disarmed.
Notice!
Single button disarming from STAY Mode 2 reports as User Code00.
6.6
Control Panel System Operations | en 55
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji