Bosch B450 Przewodnik Instalacji Strona 143
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Alarm Restore Code
Location 392 is ignored when programming the Alarm Restore code and is global for all zones.
A zone Restore Report is sent only to the receiving party to which the zone is allocated (for
example, Receiver 1 or Receiver 2).
RF Receiver Trouble Report
RF Signal Jamming (Contact ID Event Code 344, Point ID Code 821)
RF Receiver Tamper Switch (Contact ID Event Code 341, Point ID Code 821)
RF Receiver Failure (Contact ID Event Code 333, Point ID Code 821)
RF Receiver Trouble Restore Report
An RF Receiver Trouble Restore Report is sent to the base station receiver when the RF
receiver no longer registers RF Signal Jamming, RF Receiver Tamper Switch, or RF Receiver
Failure.
RF Low Battery Report
An RF Low Battery Report (Contact ID Event Code384) is sent to the base station receiver
when the battery voltage on a wireless zone falls below its corresponding low battery
condition. An RF Low Battery Restore Report is sent on the first valid signal after the battery is
replaced.
Arm/Disarm Reports
A Disarm Report (Contact ID Event Code 401) is sent to the base station receiver when the
system is disarmed from AWAY Mode. An Arm Report (Contact ID Event Code 401) is sent at
the end of Exit Time when the system is armed in AWAY Mode.
If an expanded format is selected, this code is used as the Expansion Code and the user
number that armed or disarmed the system follows in the same transmission.
To enable Arm/Disarm Reports in STAY Mode:
Select Option 2 in Location 178. To enable Arm/Disarm Reports only after a previous alarm,
select Option 1 in Location 178.
Codepad Duress Report
A Duress Report (Contact ID Event Code 121) is sent to the base station receiver when 9 is
added to the end of any valid User Code used to disarm the system. This alarm is always
silent. A Duress Alarm can be activated during Exit Time. In other words, if the system is
armed and then disarmed by adding 9 to the end of the User Code before Exit Time expires, a
Codepad Duress Report is transmitted. Adding 9 to the end of a User Code when arming the
system does not cause a Duress Alarm.
If you want a 3 to activate a Codepad Duress Alarm instead of 9, select Option 2 in Location
498.
Notice!
Restore Reports are not sent for this event.
17.6
17.7
17.8
17.9
17.10
17.11
Control Panel Reports | en 143
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.121 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji