Bosch B450 Przewodnik Instalacji Strona 37
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
1. Access your router’s web interface and find the IP address of the B426, e.g.
“192.168.226.127”. You can input the B426 IP address https://192.168.226.127 in your
PC IE to check some B426 parameters, notice the protocol is “https” not “http”.
2. Open A-Link Plus. Enter “admin” (lower case) as operator, “ADMIN” (all capitals) as
password.
3. Click File > Communication Setting and select the Local IP Address of your computer.
Enter the local port number.
4. Add a new customer, then open the customer interface.
5. Enter the customer information, and the Control Panel IP Address you found in step 1,
e.g. “192.168.226.127”.
6. Enter 7700 in the Control Panel Port field.
7. Open the Control Panel Configuration menu. Select Solution 2000 or Solution 3000
according to your control panel type.
8. Open the Link menu. Select Network Connect (TCP/IP SSL) and click Connect. A-Link
tries to connect to the control panel using the B426. A-Link is connected to the control
panel when the Connect button changes to Disconnect.
Connect A-Link Plus to the control panel using the B426
1. Click Upload from Control Panel. A-Link reads the parameters from the control panel and
displays the parameter value differences between the A-Link database and the control
panel database in a dialog box. There should be different parameters for “Network
Module 1” and “Network Module 2”.
2. Click “Yes” to replace the parameter values in A-Link with the parameter values in the
control panel.
3. Open the Control Panel Configuration menu and access the Solution2000/3000
configuration interface. Select Network Module Programming. Change the parameters for
Module 1 and Module 2 as indicated in the following table:
Parameter
Module 1 Module 2
Basic Network Settings Enter the B426 IP address,
example:192.168.226.127
Mail Information Change the parameters for
the sending mailbox if you set
the Email receiver.
Change the parameters for
the sending mailbox if you set
the Email receiver.
Maintenance > Web Access
Enable
Enable Enable
Primary Network Information
> Primary Network Access
Point Name
Enter the point name for your
GPRS server
Return to the Link menu and reconnect the control panel. Click Download to Control Panel to
complete the process.
Check the parameters in the control panel to verify the parameter value changes were
successfully downloaded.
Configure the control panel with a codepad:
1. Enter the Installer passcode (the default is 1234) and press [#] to enter Installer’s
Programming Mode.
Control Panel
Accessories | en 37
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji