Bosch B450 Przewodnik Instalacji Strona 67
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Notice!
As each zone is selected to be isolated, the corresponding zone indicator flashes. If you make
a mistake, enter the incorrect zone number and press [STAY]. This zone is no longer selected
to be isolated and the zone indicator is extinguished.
4. Press [AWAY]. Two beeps sound and the system returns to the disarmed state. The
indicators for the zones you selected and the STAY indicator are extinguished.
Example
If you want to select zones 2, 5, and 6, enter:
[1 2 3 4 4][AWAY][2][STAY][5][STAY][6][STAY] [AWAY]
You can disable selected zones to be automatically isolated for STAY Mode 2 at any time.
To disable STAY Mode 2 zones:
Enter your passcode and press [4][AWAY] [AWAY].
Turning Report Monitor Mode On and Off
Report Monitor Mode allows you to use the remote codepad for visual representation of data
transmissions between the control panel and the base station receiver. The transmission
sequence is also shown in this mode.
The codepad beeps once every two sec when Report Monitor Mode is active, whether the
system is in Installer’s Programming Mode or normal operating mode. The first five indicators
show the progressive steps during a transmission to the base station receiver for Receiver 1,
Indicator 9-13 for Receiver 2.
After you activate Report Monitor Mode, hold down [9] until two beeps sound to initiate a
Test Report.
Report Monitor Mode Indications
Zone indicator
Dialing event
1, 9 Telephone line seized
2, 10 Dialing phone number / Network connect
3, 11 Handshake received
4, 12 Data is being transmitted
5, 13 Kiss-off received
None Telephone line released / idle
Zone Indicator 1-5 for Receiver1, Zone Indicator 9-13 for Receiver 2.
To turn Report Monitor Mode on:
1. Enter the Installer Code and press [6][AWAY]. Three beeps sound.
2. Press and hold [9] until two beeps sound. A Test Report is sent.
To turn Report Monitor Mode off:
Enter the Installer Code and press [6][AWAY]. Two beeps sound.
Notice!
You must exit from Report Monitor Mode to resume normal operations.
7.1.6
Control Panel System Functions | en 67
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch B450
(20 strony)
(24 strony)
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji