Bosch DS7200V2-EXP Podręcznik Użytkownika Pobierz pdf (Strona 113)

DS7200V2-EXP | Expert Programming Guide | 4. Control Panel Programming EN | 113

Bosch Security Systems | 8/04 | 4998153891C

Table 25: Output Function Types (continued)

Digit 1 Digit 2 Function Type Description

0 11 Exit Delay, Entry Delay, Chime Output activates at the start of Exit Delay or Entry Delay. For Steady or

Pulse modes, the output remains activated until Entry or Exit Delay ends.

The output also activates whenever a Chime zone is faulted. The output

does not activate on Chime if Chime Tone is turned off.

0 12 Phone Line Fail Output activates when a Phone Line Fail condition is detected. For

Steady or Pulse modes, the output remains activated until the condition is

cleared. This output works independently of Phone Line Fault

Response Options (page 18).

0 13 Ack Received (any report) Output activates when the acknowledgement for any report is received.

For Steady or Pulse modes, [System Reset] resets. This output type is

event-driven. See Mode (Steady, Pulse, One Shot), Output ## on page

117 for more information.

0 14 AC Fail Output activates when a AC Fail condition is detected. For Steady or

Pulse modes, the output remains activated until the condition is cleared.

0 15 Low or Missing Battery Output activates when a control panel Low or Missing Battery condition

occurs. For Steady or Pulse modes, the output remains activated until the

condition is cleared.

1 0 PO 2 (on-board) Siren

Supervision Fail

Output activates when a Siren Supervision Fail condition is detected. For

Steady or Pulse modes, the output remains activated until the condition is

cleared and the [System Reset] key is pressed.

1 1 Sensor Trouble Monitor Output activates when a Sensor Trouble Monitor condition is detected in

conjunction with the selection made for the Sensor Monitor Time setting.

For Steady or Pulse modes, the output remains activated until the Sensor

Monitor Trouble condition is cleared.

1 2 Duress, [#][4][7] (reset) resets Output activates whenever a Duress PIN is entered. For Steady or Pulse

modes, the output remains activated until user presses [System Reset].

1 3 User Tamper, [#][4][7] (reset)

resets

Output activates on a User Tamper event. For Steady or Pulse modes,

the output remains activated until user presses [System Reset].

1 4 Arming Beeps (for

keyswitch/RF arming)

Disarm/All On/Perimeter Only/Partial On Beeps for keyswitch/RF arming.

1=Off, 2=All, 3=Perimeter Only. Mode and Time parameters do not

apply. This function works in conjunction with Address 1039. See

Global Output Options on page 107. Available for on-board outputs

only.

1 5 Bell Time – Starts on any

Alarm Event. PIN entry Stops.

Activates on Bell Test.

Output activates on any alarm event. Entering PIN terminates Bell Time.

For Steady and Pulse modes, the output remains activated for the

duration programmed in the Bell Time parameter.

1 6 Strobe Activates on Bell Time or output function as programmed. See Strobe

Output Type Options on page 109. PIN entry resets the function.

1 2 ... 108 109 110 111 112 113 114 115 116 117 118 ... 155 156

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch DS7200V2-EXP Podręcznik Użytkownika Strona 113

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch DS7200V2-EXP