Bosch DS7200V2-EXP Podręcznik Użytkownika Pobierz pdf (Strona 51)

DS7200V2-EXP | Expert Programming Guide | 4. Control Panel Programming EN | 51

Bosch Security Systems | 8/04 | 4998153891C

Area Idle Text

• Address:

− Area 1 Idle Text: 1426-1457

− Area 2 Idle Text: 1490-1521

− Area 3 Idle Text (DS7240V2 only):

1554-1585

− Area 4 Idle Text (DS7240V2 only):

1618-1649

• Default: Not Ready

• Selections: See Key/Character selection chart

All control panel text is programmed from the

text keypad in a special text-programming mode.

See Text Entry Addresses on page 7 for text

programming instructions.

This parameter provides 16 characters of

programmable text for each area displayed when

the system is idle (no alarms, no troubles, system

disarmed).

If the “Don’t Show Zone Status on Keypads” option is not enabled in the Keypad # Options parameter (page 67),

the text keypad displays “OK for All On” or “OK for Perimeter” across the second line. This indicates that all

zones are normal and the system is ready to arm All On or Perimeter Only. If a controlled zone is faulted, the

area idle text for this zone’s assigned area replaces the “OK for All On/OK for Perimeter” message.

If a zone not configured for Perimeter Only arming is faulted, “OK for Perimeter” replaces “OK for All On” on

the text keypad’s display. The system might be armed Perimeter Only, but cannot be armed All On until the

faulted zone is restored.

If the “Don’t Show Zone Status on Keypads” option is enabled, the area idle text displays continuously on the

second line when the keypad is idle (even if a zone is faulted).

If the “Don’t Show Zone Status on Keypads” option is selected, the default Area Idle Text (“Not

Ready”) should be changed. See Text Entry Addresses on page 7 for text entry instructions.

Key Character

0 + - 0 * / \ [ ] = > < # §

1 Space . 1 ? ! , @ _ & ~ : ; " ( ) ' ¿ ¡ % £ $ ¥

2 A B C a b c 2 Å Ä Ã å ä á à â ã α β Ç ç

3 D E F d e f 3 É Æ ë é è ê æ ∆ Φ δ ε

4 G H I g h I 4 ï í î ì Γ γ η ι

5 J K L j k l 5 Λ κ λ

6 M N O m n o 6 Ö ö Ñ ñ Ø Õ ø ó ò ô õ Ω µ ν ω

7 P Q R S p q r s 7 Π Σ π ρ σ

8 T U V t u v 8 Ü ü ú ù û Θ Υ θ τ υ

9 W X Y Z w x y z 9 ÿ Ξ Ψ ξ χ ψ ζ

* Moves to the address before the text block.

# Moves to the address after the text block.

A Moves cursor to the previous character position in

text block.

C Moves cursor to the next character position in text

block.

The following keys are not used in text programming

and produce an error tone when pressed: [On], [Off],

[Perimeter Only], [No Entry], [Bypass], [System Reset],

and [B].

Press [1] once to clear a character space or to enter a

blank space.

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 155 156

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch DS7200V2-EXP Podręcznik Użytkownika Strona 51

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch DS7200V2-EXP