Bosch DS7200V2-EXP Podręcznik Użytkownika Pobierz pdf (Strona 5)

DS7200V2-EXP | Expert Programming Guide | 3. How to Program EN | 5

Bosch Security Systems | 8/04 | 4998153891C

3. How to Program

3.1 Keypad Programming

3.1.1 Installer Mode/Installer Menu

A text keypad such as the DS7447E or

DS7447V2 LCD Keypad can be used for

keypad programming. The DS7445i and

DS7445V2 LED Keypads cannot be used

for keypad programming.

Use of the Installer PIN might be restricted.

See Keypad Response Options on page

70 for information on enabling/restricting

the Installer PIN.

There are three methods to access the control panel’s

programming mode. Choose a method from below and

follow its subsequent steps.

1. From a LCD (text) system keypad:

a. Enter the Installer’s PIN. The default Installer

PIN is 9876. See Installer PIN on page 63 for

instructions on changing the default Installer

PIN.

b. Press [#][4][1] to enter the Installer’s Menu.

c. Press the [8] key to enter the programming

mode.

From an Installer Keypad:

d. Set the Installer Keypad address to 0 (zero).

e. Connect the Installer Keypad to the control

panel. See “Installer Keypad” in the DS7200V2

Installer’s Guide (P/N: 4998153893) for

instructions.

f. Close the Installer Switch.

g. Enter the Installer PIN.

h. Press [#][4][1] to enter the Installer’s Menu.

i. Press the [8] key to enter the programming

mode.

Without an Installer’s PIN:

j. Remove all power from the control panel

(Mains and standby battery).

k. Close the Installer Switch.

l. Connect the Installer Keypad to the control

panel if you are using an Installer Keypad.

m. Restore all power to the control panel.

n. Locate the keypad displaying the Installer

Menu.

o. Press the [8] key.

3.1.2 Expert/Installer Programming Modes

• Installer Programming Mode: Installer

Programming Mode is the control panel’s default

programming mode. This mode allows the installer

to access only a subset of the available

programming parameters. Installer Programming

Mode follows through the addresses shown in the

programming section of the DS7200V2 Installer’s

Guide (P/N: 4998153893).

• Expert Programming Mode: When the control

panel enters the Expert Programming Mode, all of

the available programming parameters can be

accessed. This manual contains all of the available

programming parameters. Follow these steps to

enter the Expert Programming Mode:

1. Enter Installer Mode (see Installer Mode/Installer

Menu for instructions).

2. Press [7][2][4][0][#] if you are programming a

DS7240V2. Press [7][2][2][0][#] if you are

programming a DS7220V2.

3. Press [1][*]. The control panel enters Expert

Programming Mode, and the display shows

Address 0.

3.1.3 Parameter Addresses

Data for each parameter is stored at one or more

addresses. Special addresses identified as option

parameters allow you to set several options at a single

address.

There are two parts to every address displayed across

the keypad’s top line:

• Adr: XXXX: The number following “Adr”

indicates the current address displayed.

• D=X: “X” indicates the data digit selection for the

address currently displayed.

Adr: 0000 D=0

To view a specific address, enter the 4-digit address

number and then press [#].

For example, to go to Address 0221, press the

following keys in this order: [0][2][2][1][#].

Leading zeroes can be omitted. Pressing [2][2][1][#] is

the same as pressing [0][2][2][1][#].

Adr: 0000 D=0

0221

To scroll forward one address at a time, press [#]. To

scroll back one address at a time, press [*].

1 2 3 4 5 6 7 8 9 10 ... 155 156

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch DS7200V2-EXP Podręcznik Użytkownika Strona 5

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch DS7200V2-EXP