Bosch DS7200V2-EXP Podręcznik Użytkownika Pobierz pdf (Strona 114)

DS7200V2-EXP | Expert Programming Guide | 4. Control Panel Programming EN | 114

Bosch Security Systems | 8/04 | 4998153891C

Table 25: Output Function Types (continued)

Digit 1 Digit 2 Function Type Description

1 7 Silent Alarm Activated by alarm on non-fire zones programmed for No Alarm Output.

Follows Bell Time for Steady and Pulse modes. PIN stops. The following

conditions activate Silent Alarm:

- ABC Key programmed for Fire or Emergency and no Alarm Output

- RF Keyfob programmed for Fire or Emergency and no Alarm Output

- A zone programmed for Fire or Fire with Verify and no Alarm Output

- Any zone not programmed for Invisible Panic that is programmed for no

Alarm Output

- Any armed zone programmed as a controlled type that goes from

Supervised to Missing and programmed for no Alarm Output

- Any armed keyswitch programmed for no Alarm Output that goes from

Supervised to Missing or Short to Missing

- Any zone programmed for Swinger Count and Swinger Count for Alarm

Output that reaches its programmed value

1 8 Alarm – All On, Perimeter Only,

and Partial On Arming, Non-fire

24 hour alarms

Activated by alarm on zone when All On, Perimeter Only, and Partial On

Armed, or by alarm on Non-fire 24 hour zone, and by user/installer ‘Bell

Test’. Follows Bell Time for Steady and Pulse modes. PIN resets. Follows

programming for ‘Alarm’ output types.

1 9 Alarm – Perimeter Only and

Partial On Arming Modes, Non-

fire 24 hour alarms

Activated by alarm on zone when Perimeter Only, and Partial On Armed,

or by alarm on Non-fire 24 hour zone, and by user/installer ‘Bell Test’.

Follows bell time for Steady and Pulse modes. PIN resets.

Follows programming ‘Alarm’ output types.

1 10 Alarm –Controlled zones, 24-hr

zones (Fire and Non-Fire)

Activated by alarm on zone when All On, Perimeter Only, and Partial On

Armed, or by alarm on Fire and Non-fire 24 hour zone, and by

user/installer ‘Bell Test’. Follows bell time for Steady and Pulse modes.

Pulses in Temporal Code 3 format for Fire alarms only. PIN resets.

Off-board outputs cannot provide output in Temporal Code 3 format

(only on-board outputs). Off-board outputs provide a steady output.

Follows programming for ‘Alarm’ output types. Temporal Code 3 for

Fire alarms only.

1 11 Fire Alarm Activated by alarm on Fire zone, and by user/installer ‘Bell Test’. Follows

Bell Time. Pulses in Temporal Code 3 format. Mode and Time parameters

do not apply. PIN resets. Off-board outputs cannot provide output in

Temporal Code 3 format (only on-board outputs). Off-board outputs

provide a steady output. Follows programming for ‘Alarm’ output

types.

1 12 Fire Alarm, Latching Activated by alarm on Fire zone, and by user/installer ‘Bell Test’. Does not

pulse in Temporal Code 3 format. Mode and Time parameters do not

apply. [#][4][7] resets. Follows programming for ‘Alarm’ output types.

1 13 Fire Verification/Reset Normally on. Turns off on activation to reset smoke detectors. Verification

for Fire Verification Zone Function type and [System Reset] activate

output for approximately 15 sec. Mode and Time parameters do not apply.

Used for 4-wire smoke detectors.

1 14 System Trouble Activates on any System Trouble. Resets when all system troubles are

clear.

1 15 [O] Key (Trapezoid Key on RF

Key Fob)

Activates when [O] (Trapezoid key on RF Keyfob is pressed. [System

Reset] resets. Pressing [O] again also resets output when Output Mode

is set to Toggle. This output type is event-driven. See Mode (Steady,

Pulse, One Shot), Output ## on page 117 for more information.

1 2 ... 109 110 111 112 113 114 115 116 117 118 119 ... 155 156

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch DS7200V2-EXP Podręcznik Użytkownika Strona 114

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch DS7200V2-EXP