Bosch DS7200V2-EXP Podręcznik Użytkownika Pobierz pdf (Strona 31)

DS7200V2-EXP | Expert Programming Guide | 4. Control Panel Programming EN | 31

Bosch Security Systems | 8/04 | 4998153891C

Walk Test Start/End Report Routing

• Address: 0248

• Default: 5 (No reports, Events to Log/Printer)

• Selections:

− 0 = No Reports, no Events to Log/Printer

− 1 = Reports to Destination 1, Events to Log/Printer

− 2 = Reports to Destination 2, Events to Log/Printer

− 3 = Reports to Destinations 1 & 2, Events to Log/Printer

− 4 = Reports to Destination 2 only on Destination 1 Comm Fail Event, Events to Log/Printer

− 5 = No reports, Events to Log/Printer

This is a global (affects all areas) parameter. See “Communication Failure (Comm Fail)” for a description of the

Comm Fail event , and “Dialing Attempt Tables” for the dialing sequence in the DS7200V2 Installer’s Guide

(P/N: 4998153893).

Automatic Test {137} Report Options

• Address: 0249

• Default: 0

• Selections: 0 to 4, 8 to 12

Enter This Data Digit to Select Options

Automatic Test Report Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

No Automatic Test Report Options

•

Test Report Only if System is Armed

• •

Defer Test Report if Other Report Sent in Test

Interval

• •

Test Reports for All Areas (else Area 1 only)

•

Call RPS at Test Time (after Test Report)

• • • • •

Use these options to configure the Automatic Test {137} report. If “Call RPS at Test Time” is enabled, a variety of

tasks could be accomplished at this time, including downloading the log to RPS.

• Test Report Only if System is Armed: This option sends a test report only if the system is armed.

• Defer Test Report if Other Report Sent in Test Interval: If another report is sent during the test interval,

this option defers the test report until the end of the test interval.

• Test Reports for All Areas (else Area 1 only): If selected, this option generates a test report for all enabled

areas. For the DS7240V2, this option applies to Areas 1 through 4. For the DS7220V2, this option applies to

Areas 1 and 2.

• Call RPS at Test Time (After Test Report): If selected, this option calls RPS at test time after the system

sends the test report. The Remote Programming Call Back Phone Number should be programmed. See

Remote Programming Call Back Number on page 16 for more information.

Automatic Test {137} Report Time

• Address: 0250 to 0253

• Default: 0000 (Test reports disabled)

• Selections: 0 to 9

Enter the time of day for the Automatic Test. Use 24-hour format (HHMM) where midnight is 2400, noon is 1200

and 12:01 am is 0001. Enter one digit in each address so that Addresses 0250 and 0251 are the hour, and 0252

and 0253 are the minute. An entry of 0000 (the default setting) disables the Automatic Test {137} report.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 155 156

Komentarze do niniejszej Instrukcji

Brak uwag

Bosch DS7200V2-EXP Podręcznik Użytkownika Strona 31

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Bosch DS7200V2-EXP